pasoblibrary.blogg.se

1. MS DOS 6.22 ISO VMWARE INSTALL
2. MS DOS 6.22 ISO VMWARE PLUS
3. MS DOS 6.22 ISO VMWARE FREE
4. MS DOS 6.22 ISO VMWARE WINDOWS

Step 12: Once everything is done, remove all the disks and press Enter. Step 11: When Setup asks for the third disk, do the same procedure as above. Step 10f: Do this for the next disk-switch. Step 10: When the setup program asks for disk two, to make it recognize the second disk, do the following: The installation will take a little bit since its being run off of floppies.

MS DOS 6.22 ISO VMWARE INSTALL

Step 9: The installation program will now install MS-DOS 6.22 onto your hard disk image. Ninety nine percent of the time, C:\DOS is perfectly acceptable. Step 8: Now it will ask where you want to install the DOS files. If not, you can change them by using the arrow up and arrow down keys. If you live in the United States, these settings are most likely correct. Step 7: It will ask for the date, time, country, keyboard layout now. Step 6: Setup will once again begin to load, and eventually, it will. Step 5: Keep the floppy in the drive and press Enter. Step 4: Setup will either give you two options: Configure disk or Exit Setup. Note: To interact with the virtual machine, you must click on it. Step 3: Once the setup program loads, read whatever it says and press Enter. Step 2: The virtual machine will boot and the setup program will begin the load.

Step 1: Insert Disk 1 of the MS-DOS 6.22 set into the floppy drive and click �Start this Virtual Machine�. Once it�s done, you will see a summary of all the settings for your Virtual Machine. Step 10: Click Finish, and the disk will be created. Step 9: Choose the filename for the disk. Don�t worry about the Split disk into 2GB files option. If you have 2GB readily available, choose �Allocate all disk space now�. Step 8: For disk size, 2GB is PLENTY for WFW 3.11, MS-DOS 6.22, and some utilities. Use it only if you know what you are doing. If you are reading this, you probably don�t have a disk image already for use. For most, creating a new virtual disk is good enough. Step 7: Choose the type of disk image you want. In the Networking HOWTO for WFW 3.11, this is covered. Step 6: For Network Connection, this can get a bit complicated. Except with some applications, for example, IE setup will not run with more than 40MB of memory. Step 5: For memory, I would set it to 32MB. Step 4: Choose the name of your Virtual Machine, and choose the location for the Disk Images and configuration files, then hit Next.

MS DOS 6.22 ISO VMWARE WINDOWS

Step 3: For Guest Operating System, choose Windows 3.1, then hit Next. Step 2: Click Next, and select Custom and click Next again.

MS DOS 6.22 ISO VMWARE FREE

There are no doubt some free ones around too.Ĭheers IB ianboag Posts: 12 Joined: 15.Step 1: Open up VMware and click New Virtual Machine.

I don't work for the MagicISO people - it's not a free product - but it is easy to use and worked fine for me. Alternatively you can use a floppy disk image (MagicISO makes them too) in the same way. Change the boot to F10 etc and this time you will boot off drive C with the "CD" available as drive R.Īnything else you need to move on to the HD is easily done by getting an ISO writer (eg MagicISO), putting the stuff into an ISO and attaching the ISO as the CD drive for the VM. Reboot the VM and do the F2 setup thing again. Copy CD1.SYS and MSCDEX.EXE from C:\DOS to C:\. Then copy A:CONFIG.SYS to C:CONFIG.SYS and A:AUTOEXEC.BAT to C:AUTOEXEC.BAT. It's a good idea at this point to make a DOS subdirectory (C: then MD \DOS and CD \DOS). Once that is finished you have a bootable drive C. When that comes back to A:> type FORMAT C: /S. Type FDISK - when it tells you to remove the diskette, reboot the VM.

MS DOS 6.22 ISO VMWARE PLUS

It will boot up from drive A plus install a CD drive as R.Īt this point you have the A:> prompt. Go to the bit to make the VM boot off CD. While it is booting hit F2 - this will give you the BIOS setup.